The camshaft position sensor helps your car engine transfer data so that it can start running the moment the ignition is made. But the moment you feel the engine overheating as if it has the flu or if it shuts down randomly, you can assume that there’s something wrong with the camshaft sensor.
It won’t be very useful for you to try and fix the sensor by yourself. The only action for you to take is to replace it. Now knowing how to replace camshaft position sensors aren’t an easy task. Having both the materials and knowledge is vital for you to carry out this task. We will help you know exactly what to do for this now.
Steps For Replacing A Camshaft Position Sensor
Just getting the best chevy 350 cam isn’t enough. You have to know how to replace a camshaft position sensor as well. To replace a camshaft position sensor, also known as the CMP, there are some steps you will need to follow for the task to be done successfully. Below the steps are given:
Step 1: Identify The Problem Or Cause
There are various problems that could have caused the camshaft position sensor to fail or get damaged. Some of those causes could most likely be bad wiring, overheating, crank walks, pollution or impurities in the camshaft, damage to the belt, car accidents or collisions that happened before, and many more. If these problems have occurred, then you know it is time to remove and replace it.
Step 2: Get The Right Tools And Materials
Owning a car usually means you already will have tools like torque wrench in your garage so that you can fix-up multiple problems that your car engine causes. Then again, you might have run out of the tools and materials, they might have been worn out, or you might have a limited or a small set of equipment.
In that case, you will have to go out to the store and get the necessary tools to help you replace your camshaft sensor. The equipment you will need includes a flashlight, lubricant, a ratchet that is about 14 inches, and some drive sockets that are also 14 inches.
Step 3: Preparing The Car
Drive your car into a place that is clean on the ground and has lots of lighting. You will need to set your tools nearby and have enough light to see clearly inside the engine and work on the replacement. You can use the flashlight in case you do not have enough lighting. If it is necessary, you can have someone help by holding the light for you as you work on the camshaft position sensor.
After the car is set in a required place, you need to make sure to turn it off so that the engine can cool down. After it cools down, then you can pop the hood open and work on it.
Step 4: Remove The Old Or Damaged Camshaft Position Sensor
After you have all the lighting prepared, you need to find the location of the 302 performance camshaft sensor. Once you do, make sure to disconnect the current sensor’s electrical connector or plug. You just have to press and pull on the tab quickly. There will be bolts that are connected to the sensor. Take your ratchet and a socket and proceed to remove the bolts. You can then easily pull the sensor off.
Step 5: Install The New Camshaft Position Sensor
Take the new camshaft sensor out of its packaging and apply the grease or lubricant on the gasket. The grease you use here must be silicone-based. The tip of the new camshaft sensor should be clean so that you can twist it into its new position easily.
After placing the sensor in the proper place, you can then screw those bolts back on so that the sensor is attached. Plug or connect the electrical plug to the sensor again. Then you can close the car’s hood and start your engine. It should run smoothly now.
Problems occurring with camshaft position sensors is not uncommon at all. Having the knowledge on how to replace camshaft position sensors is helpful during situations like this. This knowledge will also help you with installing other auto parts like 2007 toyota 4runner shocks and struts or turbo for 12v cummins.
There are many causes for engine failure, and the ones involved in damaging your camshaft sensor is definitely one of them. You might not notice the problems during the early stages, but the symptoms of your car not working properly should help you know later on. Right then, you can make the right decision to replace the sensor and have a safe drive.
Leave a Reply